#Does mii instructions update#
#Does mii instructions driver#
#Does mii instructions code#

Having additional targets increases the reliability of the ARP monitoring.Д®nable ARP interface bonding> set 0 link-monitoring=arp interface bonding> set 0 link-monitoring=arp arp-ip-targets=172.16.0.1 If only one target is set, the target itself may go down. It is possible to specify multiple ARP targets that can be useful in High Availability setups. Meaning of each option is described later in this article. Otherwise all replies from the ARP targets will be received on the same link which could cause other links to fail.ДЄRP monitoring is enabled by setting three properties link-monitoring, arp-ip-targets and arp-interval. If balance-rr and balance-xor modes are set, then the switch should be configured to evenly distribute packets across all links. This also gives assurance that traffic is actually flowing over the links. It is not possible to use both methods at the same time due to restrictions in the bonding driver.ДЄRP monitoring sends ARP queries and uses the response as an indication that the link is operational.

#Does mii instructions driver#

In the above example, if one of the bonded links were to fail, the bonding driver will still continue to send packets over the failed link which will lead to network degradation.Д«onding in RouterOS currently supports two schemes for monitoring a link state of slave devices: MII and ARP monitoring. It is critical that one of the available link monitoring options is enabled. Note: bonding interface needs a couple of seconds to get connectivity with its peer.

Add bonding interface on interface bonding> add slaves=ether1,ether2ДЄnd on interface bonding> add slaves=ether1,ether2ДЄdd addresses to bonding ip address> add address=172.16.0.1/24 ip address> add address=172.16.0.2/24 interface=bonding1.

Make sure that you do not have IP addresses on interfaces which will be enslaved for bonding interface!.

To make this possible, follow these steps: Let us assume that we have 2 NICs in each router (Router1 and Router2) and want to get maximum data rate between 2 routers. More details can be found in the LAG interfaces and load balancing page. Interface bonding creates a virtual interface that can load balance traffic over multiple interfaces.

These files are generated during the 'prepare SD card' steps.Note: Interface bonding does not create a interface with a larger link speed.

#Does mii instructions code#

Of course, the boot2 code is limited in size, so instead it loads certain files on the SD card instead. This allows it to execute some custom code before the Wii menu boots, meaning it can serve as brick protection. If your Wii is compatible, BootMii will replace the normal boot2 code. Unfortunately, Nintendo later patched boot1 on newer consoles, making those consoles always incompatible. Since boot1 cannot be modified, this means that any 'BootMii as boot2' compatible Wiis will always be compatible. We can see that there are various 'booting' steps that happen before the Wii Menu is executed (which is when the health screen appears).Д«oot0 is on read-only memory and can thus never be modified.Д«oot1 can be written, but various read-only checks prevent anyone from doing so.Д«oot2 however, can be modified on older consoles due to a bug in boot1 on those systems. The booting procedure of the Wii goes something like this: The NAND backup function can be found under the 4th button, then the 1st button (the highlighted button in the below screenshot). To make your Wii more brick-proof, make a backup of the NAND before making major changes to the Wii memory. You can navigate through the menu with a GameCube controller or the buttons on the Wii itself ( Power = right, Reset = OK). In the Homebrew Channel, press home to access the menu, and choose 'Launch BootMii'. If you only installed BootMii as IOS, you need to launch BootMii through the Homebrew Channel instead. Every time you boot the Wii with the prepared SD card inserted, you will see the BootMii menu. IT IS HIGHLY RECOMMENDED THAT YOU CREATE A NAND BACKUP AS SOON AS POSSIBLE AFTER INSTALLING BOOTMII. This backup can also be restored later on if needed, providing an additional brick protection. BootMii has the ability to dump this memory to the SD card (as the file NAND.bin). One of the features BootMii provides is the ability to create a NAND backup. This is why BootMii can't be installed as Boot2 on those Wii's.

Unfortunately, Nintendo already knew about it before it was even released, so they updated boot1 (which loads boot2) on newer Wii's.

#Does mii instructions update#

As boot2 is normally not updated through a wii system update (which was proven wrong with the 4.2 update!), this is the best brick protection you can get. BootMii is a modification of boot2, which loads the system menu when booting the Wii.